VIP Vision VSBKTA152E: a coated aluminium pole mount with two band clamps that carries a VIP Vision junction box or wall mount on a pole.
- ✓Fits poles 80 to 150 mm in diameter
- ✓3 kg load rating, 0.32 kg
- ✓Takes VSBKTA137, VSBKTA130E, VSBKTA122 and other VIP Vision boxes
- ✓34 mm centre cable hole, multiple hole patterns
- ✓Rated −40 °C to 60 °C, 4 year warranty
Description

Put the camera on a pole,
80 to 150 mm across.
The VIP Vision VSBKTA152E is a coated aluminium pole mount with two band clamps. It carries a junction box or wall mount, and the camera on it, on a pole from 80 to 150 mm in diameter.
In one sentence: the VIP Vision VSBKTA152E is a dual clamp pole mount bracket in coated aluminium, rated for 3 kg, that fixes a VIP Vision junction box or wall mount to a pole 80 to 150 mm in diameter.
Pole mount only. Camera and junction box are separate.
This listing is the VSBKTA152E plate and two band clamps. VIP Vision's guide always fits it behind a junction box or wall mount, never straight onto the camera. Check the box or mount your camera needs below.
- VSBKTA152E mounting plate with two band clamps (as pictured)
- The junction box or wall mount VIP Vision lists for your camera (see the table below)
- A compatible VIP Vision camera
- A pole 80 to 150 mm in diameter
From a wall-only camera to a pole.
Most VIP Vision turrets, domes and bullets are made to screw onto a wall or a junction box. The VSBKTA152E gives that box or mount a flat plate on a pole, held by two band clamps, so the camera can go on a driveway post, a car park light pole or a yard column.

Clamps
Two band clamps, one plate.
The two clamps wrap round the pole and tighten with a screw adjuster. VIP Vision rates the bracket for poles from 80 to 150 mm across and a 3 kg load.

Fitted
Box on the plate, camera on the box.
VIP Vision's drawing shows a junction box screwed to the plate with the dome camera underneath. The plate has a 34 mm centre hole for the cable and several hole patterns for different boxes and mounts.
How it goes in
Clamp, fix, cable, camera.
01
Clamp it to the pole
Wrap the two band clamps round a pole 80 to 150 mm across and tighten them with the plate at the height and direction you want.
02
Fix the box or mount
Screw the junction box or wall mount for your camera to the plate, using the hole pattern that matches it.
03
Bring the cable in
Feed the cable through the 34 mm centre hole into the box, and make the joints inside it.
04
Fit the camera
Screw the camera onto the box or mount, aim it and check the picture.
At a glance
VSBKTA152E
Show specs
Type
Dual clamp pole mount bracket
Pole diameter
80 to 150 mm
Load rating
3.00 kg
Materials
Coated aluminium plate, two band clamps
Plate size (VIP Vision drawing)
125.6 × 114 × 20 mm
Centre cable hole
34 mm diameter
Hole patterns (VIP Vision drawing)
56, 70 and 84 mm circles with M4 holes; 4 × M6 at 48 × 90 mm
Weight
0.32 kg
Operating conditions
−40 °C to 60 °C, 90% RH maximum
Used with
A VIP Vision junction box or wall mount (see the table below)
Colour
White plate
Warranty
4 years

VIP Vision dimension drawing, mm [inch].
Works with
Which box or mount goes on it
From VIP Vision's 2025 accessory compatibility guide. The camera goes on the box or mount, and that goes on the VSBKTA152E. Check your model with us first.
Show all camera models
VSIPP-4DIRMG-I3, VSIPP-6DIRMG-I3, VSIPP-8DIRMG-I3, VSIPP-6DG-ID4, VSIPP-8DG-ID4, VSIPP-8DG-ID4-B, VSIPP-8DG-ID4-P, VSIPP-8DD-ID3 turrets
VSBKTA137 or VSBKTA130E junction box, or VSBKTB205W-E or VSBKTB203W / VSBKTB2203W wall mount
VSIPL-6DIRG-I, VSIPP-4DIRG-I3, VSIPP-6DIRG-I3, VSIPP-6DIRG-I3-B, VSIPP-8DIRG-I3, VSIPP-8DIRG-I3-B, VSIPP-5DIRG-I2-P turrets
VSBKTB204W / VSBKTB2204W wall mount
VSIPU-4DIRG-IM dual lens turret
VSBKTA137, VSBKTA130E, VSBKTA122 or VSBKTA123-2 junction box, or VSBKTB203W / VSBKTB2203W wall mount
VSIPP-4BIRG-I3, VSIPP-6BIRG-I3, VSIPP-8BIRG-I3 bullets
VSBKTA134 or VSBKTA130E junction box
VSIPP-4BIRMG-I3, VSIPP-6BIRMG-I3, VSIPP-8BIRMG-I3 motorised bullets
VSBKTA135, VSBKTA130E or VSBKTA122 junction box
VSIPP-8BD-ID3, VSIPP-8BD-ID3-B dual lens bullets
VSBKTA130E or VSBKTA134 junction box
VSIPP-4BIRW-I wide-angle bullet
VSBKTA135 or VSBKTA130E junction box
VSIPP-4DIRD-I3, VSIPP-6DIRD-I3, VSIPP-8DIRD-I3 vandal domes
VSBKTA136 or VSBKTA123-2 junction box, or VSBKTB203W / VSBKTB2203W wall mount
VSIPP-4DIRMD-I3, VSIPP-6DIRMD-I3, VSIPP-8DIRMD-I3 vandal domes
VSBKTA137 or VSBKTA123-2 junction box, or VSBKTB206W / VSBKTB2203W wall mount
VSIPP-4DIRF-I2 wedge dome
VSBKTA136 junction box or VSBKTB205W-E wall mount
VSIPFE-6IR-I fisheye dome
VSBKTA137 junction box or VSBKTB203W / VSBKTB2203W wall mount
VSIPFE-5IR-I fisheye
VSBKTA136 junction box or VSBKTB203W / VSBKTB2203W wall mount
VSIPFE-12IR-I fisheye
VSBKTA132E junction box (special order) or VSBKTB302S wall mount
Pair it with
What goes on this pole mount
Junction box
VSBKTA137
Round box for VIP Vision turrets, -DIRMD-I3 domes and the VSIPFE-6IR-I fisheye.
Junction box
VSBKTA130E
Listed in VIP Vision's guide for turrets, bullets and the dual lens -ID3 cameras.
Junction box
VSBKTA122
Square IP66 box for the motorised -BIRMG-I3 bullets and the VSIPU-4DIRG-IM.
Wall mount
VSBKTB2203W
Right angle mount that VIP Vision also fits on this pole mount for many domes and turrets.
Where it is used
Where a pole mount goes.
Driveway posts
A camera on a post looking up the drive and at the gate.
Car parks
Light poles and columns over the parking bays.
Farm yards
Poles in the yard covering sheds, gates and machinery.
Building sites
Temporary poles round the site boundary.
Warehouse yards
Columns along fences and loading areas.
Schools and parks
Existing poles near paths, entries and car parks.
VSBKTA152E or VSBKTA150
| VSBKTA152E (this bracket) | VSBKTA150 | |
|---|---|---|
| Clamps | Two | Three |
| Pole diameter | 80 to 150 mm | 80 to 150 mm |
| Load rating | 3 kg | 10 kg |
| Material | Coated aluminium | Coated SECC steel |
| Weight | 0.32 kg | 1.00 kg |
| Made for | Junction boxes and small wall mounts | Larger cameras and wall mounts such as the VSBKTB305W |
Figures from VIP Vision's product specifications, the VSBKTA150 brochure and the 2025 accessory compatibility guide.
Common questions
Which cameras can go on the VSBKTA152E?
Most current VIP Vision turrets, bullets, vandal domes and fisheyes, through a junction box or wall mount. The table above lists the box or mount VIP Vision's 2025 guide gives for each model.
Does the camera screw straight onto it?
No. VIP Vision's guide always puts a junction box or wall mount between the camera and the VSBKTA152E.
What size pole does it fit?
Poles from 80 mm to 150 mm in diameter.
How much weight can it carry?
VIP Vision rates it for 3 kg, which covers the box or mount and the camera together.
Is the junction box included?
No. This listing is the plate and two band clamps. The junction box or wall mount and the camera are sold separately.
Where does the cable go?
Through the 34 mm centre hole in the plate and into the junction box, where the joints are made.
What is the difference from the VSBKTA150?
The VSBKTA150 has three clamps, is SECC steel and is rated for 10 kg, for bigger cameras and wall mounts. The VSBKTA152E has two clamps, is aluminium and is rated for 3 kg.
Can it go on a square post?
VIP Vision gives a round pole range of 80 to 150 mm. For a square post, ask us first.
What is it made of?
A coated aluminium plate with two band clamps.
Does it suit a PTZ camera?
VIP Vision's 2025 guide doesn't list it for PTZ cameras. It shows the VSIPPTZ-4IRM-I2 PTZ on the VSBKTA150 pole mount or VSBKTA151 corner mount; ask us for the right parts.
How big is the plate?
125.6 × 114 mm and 20 mm deep on VIP Vision's drawing. The bracket weighs 0.32 kg.
What warranty does it have?
VIP Vision lists a 4 year warranty for the VSBKTA152E.
Supported by InFront Technologies.
Tell us your camera model and pole size and we will list the parts: call 1300 736 970 or email [email protected].
Installation and safety
Working at height. Pole work is usually done from a ladder or elevated platform. Use safe access equipment and check the pole is sound.
Cabling. Concealed data cabling to the camera is customer cabling under AS/CA S009 and needs an ACMA-registered cabler.
Poles you don't own. Get permission before fixing anything to a power, light or council pole.
What it does not do. It is not a junction box and has no cover for the cable joints; fit the box or mount VIP Vision lists for your camera.
Figures. From VIP Vision's product specifications, dimension drawing and 2025 accessory compatibility guide.
- Dimensions
- 126 x 14 x 20mm
- Operating Conditions
- -40° ~ 60°C / 90% RH (max)
- Weight
- 0.32kg
- Weather Resistance
- N/A
- Pole Diameter
- Ø80~150mm
- Materials
- Aluminium
- Bracket Type
- Pole
- Load Bearing Capacity
- 3.00kg
- Pipe Thread
- N/A