SR-PSU-12V5A: a 12V 5A desktop power supply with an IEC mains cord and a 2.1 mm centre positive plug. With a splitter it powers a group of CCTV cameras, including Swann analogue cameras, that draw 5A or less in total.
- ✓12V DC, 5A output, centre positive
- ✓2.1 mm barrel plug (5.5 mm outside)
- ✓IEC mains cord with Australian plug supplied
- ✓Short circuit proof, auto reset, power LED
- ✓Suits Swann analogue cameras; not made by Swann
Description

One supply for a group of cameras.
12V. 5A. Centre positive.
The SR-PSU-12V5A is a 12V 5A desktop power supply with an IEC mains cord and the standard 2.1 mm centre positive plug. With a 4 or 6-way splitter it powers a whole set of analogue cameras from one power point.
In one sentence: the SR-PSU-12V5A is a 12V DC, 5A switch mode desktop power supply with a 2.1 mm centre positive barrel plug, an IEC mains cord and short circuit protection, for groups of CCTV cameras drawing 5A or less in total.
Supply and mains cord. Splitter sold separately.
To share the 5A across several cameras you need a DC splitter (4 or 6-way). Add up the current on each camera's label: together they must draw 5A (5000 mA) or less. If you are replacing a recorder's adaptor, check its plug: some recorders use a 2.5 mm plug, which this 2.1 mm plug does not fit. This supply is not made by Swann; it suits Swann and other 12V gear with the same plug.
- 12V 5A desktop power supply with DC lead
- IEC mains cord with Australian 3-pin plug
- A 4 or 6-way DC splitter for several cameras
- A power point within reach of the mains cord
Enough current for the whole system.
Six cameras drawing 500 mA each add up to 3A, well inside this supply's 5A. One supply in the cabinet and every camera runs from a single power point. For a heavy load, share the cameras across two splitters.

Mains end
IEC inlet with its own mains cord.
The supply takes a standard IEC mains cord, supplied with an Australian 3-pin plug. Input is 100 to 240V AC, 50/60Hz, 1.5A max.

The case
Desktop case with a power LED.
An inline desktop supply with a power indicator LED, so you can see at a glance it is on. It is switch mode with efficiency level IV, short circuit proof, and resets itself once a fault is cleared.
How it goes in
Set up in a few minutes.
01
Add up the cameras
Read the current on each camera's label and add them up. The total must be 5A (5000 mA) or less.
02
Fit a splitter
Plug the 2.1 mm DC plug into the socket of a 4 or 6-way DC splitter.
03
Connect the cameras
Push a splitter plug fully into each camera's 12V power socket or its extension cable.
04
Mains on and check
Fit the IEC mains cord, switch on at the wall and check the LED is lit and every camera has a picture.
At a glance
SR-PSU-12V5A
Show specs
Output
12V DC, 5A (60W)
Polarity
Centre positive: inside +12V, outer sleeve GND
DC plug
Barrel, 2.1 mm inside, 5.5 mm outside
Input
100–240V AC, 50/60Hz, 1.5A max
Type
Switch mode inline desktop supply, efficiency level IV
Protection
Short circuit proof, auto reset
Indicator
Power LED
Mains
IEC inlet; IEC mains cord with Australian 3-pin plug supplied
Approval
Australian approved
DC lead
About 1.8 m
Camera budget
All cameras together 5A or less, e.g. 6 × 500 mA = 3A
Suits
12V DC CCTV cameras and recorders with a centre positive 2.1 mm plug, including Swann analogue systems
Not for
2.5 mm DC sockets, 24V AC cameras, PoE network cameras, 48V NVRs
Maker
Generic supply, not made by Swann
Colour
Black

Looking into the end of the plug: the inside contact is +12V and the outer sleeve is ground (0V).
Pair it with
What goes with it
Splitter
6-way DC splitter
One 2.1 mm socket to six plugs. The splitter has no published current rating, so ask us before running more than 2A through one.
Splitter
4-way DC splitter
For four cameras. Same 2.1 mm plugs and sockets.
Custom leads
DC plug and socket with screw terminals
Make up your own power runs to cameras further away, without soldering.
Smaller job
Only one or two cameras?
Our 12V 1A and 12V 2A plug-packs plug straight into the wall and suit smaller loads.
Where it is used
Where it is used
Whole-house analogue CCTV
One supply and a 6-way splitter powering every camera from the recorder cabinet.
Swann camera kits
Replacing a pile of plug-packs on a Swann analogue kit whose cameras take 12V DC on a 2.1 mm plug.
Shops and offices
A single, tidy supply for the cameras on a small business system.
Infrared illuminators
12V IR illuminators with a 2.1 mm plug, for example one drawing 2.5A with 2.5A to spare.
Installer van stock
The bigger 12V supply for jobs where a plug-pack is not enough.
Other 12V gear
Equipment that takes 12V DC on a centre positive 2.1 mm plug and draws 5A or less.
SR-PSU-12V5A or the 12V 2A plug-pack
| SR-PSU-12V5A (this supply) | SR-PSU-12v2A | |
|---|---|---|
| Output | 12V DC, 5A | 12V DC, 2A |
| Plug | 2.1 mm, centre positive | 2.1 mm, centre positive |
| Form | Desktop case with IEC mains cord | Plug-pack, pins on the case |
| Cameras at 500 mA each | 6 on a 6-way splitter, using 3A of the 5A | Up to 4, using the full 2A |
| Power LED | Yes | Not stated |
| Best for | A whole camera system | A DVR, or a few cameras |
Same 12V centre positive plug. Choose the 5A supply when your cameras add up to more than 2A, or when you want every camera on one supply.
Common questions
How many cameras can it run?
As many as add up to 5A (5000 mA) or less. Six cameras at 500 mA each is 3A. Check each camera's label and allow for the extra draw of infrared at night. For more than 2A through one splitter, ask us first.
Is this a genuine Swann part?
No. It is a generic 12V 5A supply that suits Swann analogue cameras and other 12V gear with a centre positive 2.1 mm plug. Swann does not make it.
Does it come with a mains cord?
Yes. It is supplied with an IEC mains cord with an Australian 3-pin plug.
Does it come with a splitter?
No. Add our 4 or 6-way DC splitter to run several cameras from it.
Can I replace my DVR's adaptor with it?
Yes, if the old adaptor reads 12V DC, 5A or less, centre positive, with a 2.1 mm plug. Some recorders use a 2.5 mm plug, which this plug does not fit, so compare them first.
Is a 5A supply safe on a camera that only needs 500 mA?
Yes. Equipment only draws the current it needs. What must match is the voltage (12V DC), the polarity (centre positive) and the plug size.
What happens if something shorts out?
The supply is short circuit proof and resets itself automatically once the fault is removed. Find and fix the short before powering the cameras again.
What does centre positive mean?
The inside of the plug is +12V and the outer sleeve is ground. Equipment wired the other way round can be damaged, so check the symbol on your camera or old adaptor.
Is it approved for Australia?
Yes. It is an Australian approved supply, and the mains cord has an Australian 3-pin plug.
How long is the DC lead?
About 1.8 m. Use a splitter and camera extension cables to reach cameras further away.
Does it work with network (PoE) cameras?
No. PoE cameras get their power through the network cable from the NVR or a PoE switch.
Can I use it outdoors?
No. Keep it indoors or in a ventilated cabinet, and run only the low-voltage leads out to the cameras.
Supported by InFront Technologies.
Not sure it covers all your cameras? Call 1300 736 970 or email your camera models to [email protected] and we will check the power budget before you buy.
Installation and safety
Mains powered. The supply plugs into a standard power point with the IEC cord. Do not open the case. A new power point needs a licensed electrician.
Do not overload it. Everything on the supply must add up to 5A or less. Leave headroom for infrared at night.
Match the voltage, polarity and plug. Only connect it to equipment that takes 12V DC, centre positive, on a 2.1 mm plug. It does not fit a 2.5 mm socket.
Ventilation. Indoor use. Do not bury the supply in insulation or seal it in a box without airflow; give it room to shed heat.
Beware of non-compliant supplies. Every mains power supply sold in Australia must be approved. Unbranded supplies from online marketplaces often are not, and some cannot deliver their rated current.
What it does not do. It is not a battery charger or a UPS, and it does not power PoE cameras, 24V AC cameras or 48V NVRs.
Figures. From our product details for this supply. No manufacturer datasheet is published for it.